tclt110. series www.vishay.com vishay semiconductors rev. 2.5, 16-may-13 1 document number: 83514 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, phototransistor output, sop-6l5, half pitch, long mini-flat package description the tclt110. series consists of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 5-lead sop-6l package. applications ? switchmode power supplies ? computer periph eral interface ? microprocessor system interface features ? smd low profile 5 pin package ? isolation test voltage 5000 v rms ? ctr flexibility availabl e see order information ? special construction ? extra low coupling capacitance ? connected base ? dc input with transistor output ? creepage distance > 8 mm ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 agency approvals ? ul1577, file no. e76222 ? csa e76222 22.2 bulletin 5a ? bsi iec 60950 iec 60065 ? din en 60747-5-5 ?fimko ?cqc note ? see the safety standard approval list agency table for more detailed information. 543 1 2 22649 ordering information tclt110# part number agency ? certified/package ctr (%) 5 ma 10 ma 5 ma ul, cul, vde, bsi, fimko 50 to 600 63 to 125 100 to 200 160 to 320 50 to 150 100 to 300 80 to 160 130 to 260 200 to 400 sop-6l5 TCLT1100 tclt1102 tclt1103 tclt1104 t clt1105 tclt1106 tclt1107 tclt1108 tclt1109 10.2 mm s op-6l5
tclt110. series www.vishay.com vishay semiconductors rev. 2.5, 16-may-13 2 document number: 83514 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the absolu te maximum ratings can ca use permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of th e time can adversely affect reliability. (1) wave soldering three cycles are allowed. also refer to assembly instruction ( www.vishay.com/doc?80054 ). note ? minimum and maximum values are testing requirements. typical values are characteristics of the device and are the result of en gineering evaluation. typical values are for information only and are not part of the testing requirements. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input reverse voltage v r 6v forward current i f 60 ma forward surge current t p ? 10 s i fsm 1.5 a power dissi pation p diss 100 mw junction temperature t j 125 c output collector emitter voltage v ceo 80 v emitter collector voltage v eco 7v collector current i c 50 ma collector peak current t p /t = 0.5, t p ? 10 ms i cm 100 ma power dissi pation p diss 150 mw junction temperature t j 125 c coupler isolation test voltage (rms) v iso 5000 v rms total power dissipation p tot 250 mw operating ambient temperature range t amb - 55 to + 100 c storage temperature range t stg - 55 to + 125 c soldering temperature (1) t sld 260 c electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input forward voltage i f = 50 ma v f 1.25 1.6 v junction capacitance v r = 0 v, f = 1 mhz c j 50 pf output collector emitter voltage i c = 1 ma v ceo 70 v emitter collector voltage i e = 100 a v eco 7v collector emitter leakage current v ce = 20 v, i f = 0 a i ceo 10 100 na coupler collector emitter sa turation voltage i f = 10 ma, i c = 1 ma v cesat 0.3 v cut-off frequency v ce = 5 v, i f = 10 ma, r l = 100 ? f c 110 khz coupling capaci tance f = 1 mhz c k 0.3 pf
tclt110. series www.vishay.com vishay semiconductors rev. 2.5, 16-may-13 3 document number: 83514 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? according to din en 60747-5-2 (vde 0884) (see figure 2). this optocoupler is suitable for safe electr ical isolation only withi n the safety ratings. compliance with the safety ratings shall be ensured by means of suitable protective circuits. fig. 1 - derating diagram fig. 2 - test pulse diagram for sample test according to din en 60747-5-2 (vde 0884); iec 60747-5-5 current transfer ratio (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit i c /i f v ce = 5 v, i f = 5 ma TCLT1100 ctr 50 600 % v ce = 5 v, i f = 10 ma tclt1102 ctr 63 125 % tclt1103 ctr 100 200 % tclt1104 ctr 160 320 % v ce = 5 v, i f = 1 ma tclt1102 ctr 22 45 % tclt1103 ctr 34 70 % tclt1104 ctr 56 100 % v ce = 5 v, i f = 5 ma tclt1105 ctr 50 150 % tclt1106 ctr 100 300 % tclt1107 ctr 80 160 % tclt1108 ctr 130 260 % tclt1109 ctr 200 400 % safety and insulation rated parameters parameter test condition symbol min. typ. max. unit partial discharge test voltage - ? routine test 100 %, t test = 1 s v pd 2.0 kv partial discharge test voltage - ? lot test (sample test) t tr = 60 s, t test = 10 s, (see figure 2) v iotm 8kv v pd 1.68 kv insulation resistance v io = 500 v r io 10 12 ? v io = 500 v, t amb = 100 c r io 10 11 ? v io = 500 v, t amb = 150 c (construction test only) r io 10 9 ? forward current i si 130 ma power dissi pation p so 265 mw rated impulse voltage v iotm 8kv safety temperature t si 150 c clearance distance 8.0 mm creepage distance 8.0 mm insulation distance (internal) 0.40 mm 0 25 50 75 125 0 50 100 150 200 300 t si - safety temperature (c) 150 94 9182-2 100 250 ir-diode i si (ma) phototransistor p so (mw) t 13930 t 1 , t 2 = 1 s to 10 s t 3 , t 4 = 1 s t test = 10 s t stres = 12 s v iotm v pd v iowm v iorm 0 t 1 t test t tr = 60 s t stres t 3 t 4 t 2
tclt110. series www.vishay.com vishay semiconductors rev. 2.5, 16-may-13 4 document number: 83514 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 3 - test circuit, non-saturated operation fig. 4 - test circui t, saturated operation fig. 5 - switching times switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit delay time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t d 3.0 s rise time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t r 3.0 s turn-on time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t on 6.0 s storage time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t s 0.3 s fall time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t f 4.7 s turn-off time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t off 5.0 s turn-on time v s = 5 v, i f = 10 ma, r l = 1 k ? , (see figure 4) t on 9.0 s turn-off time v s = 5 v, i f = 10 ma, r l = 1 k ? , (see figure 4) t off 10.0 s channel i channel ii 95 10804 r g = 50 t p t p = 50 s t = 0.01 + 5 v i f 0 50 100 i f i c = 2 ma; adjusted through input amplitude oscilloscope r l = 1 m c l = 20 pf channel i channel ii 95 10843 r g = 50 t p t p = 50 s t = 0.01 + 5 v i c i f 0 50 1 k i f = 10 ma oscilloscope r l c l 20 pf 1 m t p t t 0 0 10 % 90 % 100 % t r t d t on t s t f t off i f i c t p pulse duration t d delay time t r rise time t on (= t d + t r ) turn-on time t s storage time t f fall time t off (= t s + t f ) turn-off time 96 11698
tclt110. series www.vishay.com vishay semiconductors rev. 2.5, 16-may-13 5 document number: 83514 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example) tape and reel dimensions in millimeters fig. 6 - reel dimensions (3000 units per reel) fig. 7 - tape dimensions 22534 7.50 0.20 0.10 0.10 0.70 + 0.30 - 0.40 technical drawing s according to din s pecification s 8.20 10.80 po ss ible footprint 2.54 0.90 4.10 max. 3.80 2.00 2.30 max. 2.54 nom. 1 2 53 0.45 0.1 + 0.30 - 0.40 10.20 0.20 + 0.10 - 0.05 4 1.27 nom. pin no. 1 identification tclt1103 v yww 68 esd sticker tape slot in core 330 (13") regular, special or bar code label 17999 22662 technical drawings according to din specification 4.25 8 2.3 2 4 2.7 0.3 16 7.5 10.6 ? 1.55 1.75 ? 1.6 5 direction of pulling out
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
